A durable and stylish kitchen faucet or bath faucet blends together function and aesthetics. The well made faucet makes life a lot easier. Excellent valve mechanism and more durable finishes boost longevity and looks.

Here are six steps in choosing the right faucet for you:

1. Two-handle designs, generally goes for as low as $50, allows you to regulate the temperature more accurately. Having independent control for the hot and cold water makes adjusting the temperature easier.

The single handle faucets also known as post-mount, generally goes for $75 to $200, operate from side-mounted lever or a top-mounted knob. Most single-handle faucets have pullout spouts.

The cross-shaped design and large wing levers are the more popular designs. However, most faucets have different handles that can be attached to a faucet body for a customized look.

2. If the style of the faucet is important, begin your choosing with the type of finish. The most affordable finish for a faucet is a chrome finish. Usually priced around $60. The chrome-finish has a long warranty on scratches.

The more colorful enamel coatings generally will cost you from $20 to $200 more, and are more susceptible to scratches and chipping. Add 25 to 40 percent more to the price of coated faucets for stainless steel faucets.

3. A PVD (physical vapor deposition) finish is better than usual plated finishes but add $150 to $750 more in costs. The PVD finish is done by vaporizing the metal and glazing it with a scratch-resistant and non-tarnishing film.

Look at brushed chrome, oil-rubbed bronze and satin nickel for a rustic appeal. The brushed finish and satin finish cleverly hides scratches.

4. There are more to spouts aside from the standard straight faucets. There are high-arching goose-like spouts, great for filling pots. A pull-out faucet can get you anywhere in a sink with three-bowls. You can go from a spray mode to a stream mode with a touch. There are also restaurant-type models for those extra long hoses.

5. Know that there are four kinds of faucets.

a. The compression valve:

The compression valve uses rubber washers. The compression valve type of faucet will eventually leak but they are typically easy to repair.

b. The ball valves:

The ball valve controls the flow and temperature of the water by using a steel ball. The ball valves are washerless and easy to maintain because of this. Replacing a ball valve is readily affordable and easy to do.

c. The ceramic disk

The ceramic disk is virtually a maintenance free water faucet. It is guaranteed not to wear out but is obviously much more expensive than the ball valve or compression valve.

d. The cartridge faucet

Much like the ceramic disk, the cartridge faucet usually does not need any maintenance. Just like the ceramic disk, it has a hefty price tag.

Regardless of the type of faucet you choose. Always check the warranty and the finish.

6. You may opt for filtering faucets, costing $200 plus, to bring in purified water. Several filters are placed under the sink while others are fitted inside the spout. To set the maximum water temperature, an anti-scald faucet can be used. An electronic faucet with an infrared sensor is also available. They save on water and allow for cleaner handles.

In general, you don’t need to hand over your hard earned money to pay for good quality. Most faucets have the same basic parts and sometimes even the same finish across several price lines.

To have a streamlined, urban look, choose a faucet that is mounted on the wall, this is often used with vanity bowls.

Be sure that your faucet connection matches your sink holes. If they don’t match, you’ll have to provide more drill holes or cover the unused holes using an escutcheon plate.

All faucets in general carry at least one year warranties. Even the low-end models carry at least one year of warranty. Many faucets carry a warranty by the manufacturer that is more than one year.

Good luck choosing the perfect faucet for you.

A frost free leaky outdoor faucet, or spigot, is not just annoying; it can cost you a small fortune in water bills if left unchecked. In addition, a leaky outdoor faucet can also cause damage to your home and yard.

Fortunately, for even a novice do-it-yourselfer, a leaky outdoor faucet can be frequently fixed with just a few basic tools and about 30 minutes of time, saving you a small bundle in otherwise plumber repair costs.

Identify Source of Outdoor Faucet Leak

The first thing you need to do is to determine where the outdoor faucet leak is coming from.

First check to see if the leak is occurring around the top cap that sits just back behind the handle. Inevitably this cap becomes loose on frost free outdoor faucets and all you need to do is simply tighten it back up using your hand. Overtime this cap becomes loose due to changes in seasonal temperatures or simply from frequent use of the faucet.

Next, check to see if it is leaking directly out the spout itself.

If the leak is occurring from the faucet spout, even after you have confirmed the handle is fully turned to the closed position, then chances are there is a failed washer sitting back behind the faucet handle.

Disassembling the Outdoor Faucet

To replace the washer, first turn the water off to the outdoor faucet. Usually the shut off valve to the outdoor spigot can be found inside the home, for example in a utility room just behind the outdoor faucet. The shut off valve may also be located in the basement.

Next, turn the outdoor faucet to the full on position to relieve any pressure in it and to allow the water to fully drain from the faucet.

Now, using a screwdriver remove the screw that holds the handle onto the faucet.

With the screw removed, pull the handle off.

After removing the faucet handle, use a wrench to remove the faucet nut that sits back behind the handle.

Replace Washer and Clean Internal Faucet Area

Typically it is the washer that sits behind the faucet nut (sillcock nut) that fails. Remove it with your fingers or small screw driver and examine it for damage or wear. If you see either, replace the washer. Also, make sure the internal faucet (sillcock) is free from dirt and grime. If there is grime in it, flush it out with water.

Re-assemble Outdoor Faucet

Once you have replaced the washer and the internal faucet area is free of any grit, reattach the faucet nut cap, the handle, and the screw that holds the handle onto the faucet.

Test Repaired Outdoor Faucet

Turn the water back on at the valve within the basement or utility room to the outdoor faucet and observe water flowing freely from the faucet.

Turn the handle to the off position. If the washer or grit was the problem the leak should no longer be present.

Note that with a frost free outdoor water faucet, the actual shutoff valve sits far back into the faucet / sillcock pipe, (approximately 8 inches), so do not be surprised to see a few drips of water initially after shutting off the faucet. After a few minutes, however, you should see no more drips. With that your leaky outdoor faucet is a thing of the past!

About the Author: Over the past 20+ years Mark Donovan has been involved with building homes and additions to homes. His projects have included: building a vacation home, building additions and garages on to existing homes, and finishing unfinished homes. For more information about Home Improvement and Home Additions, and Home Remodeling and Repair visit homeadditionplus.com and homeaddition.blogspot.com.

Article Source: http://EzineArticles.com/?expert=Mark_Donovan
http://EzineArticles.com/?How-to-Fix-a-Leaky-Outdoor-Faucet&id=1460054

Fix Leaky Shower Faucet – Easy and Fast

By Yoga Priyakara

“Fix leaky shower faucet in a jiffy”, screamed the eyeball grabbing title of an article on the Internet. Now before you dismiss this as utter drivel, look beyond the hyperbolic headlines, and listen to what the experts have to say. Fixing that leaky shower faucet in your bathroom, and that too without any professional assistance, is not that prosperous a proposal. All it takes is a few very functional tools, a modicum of your time and a hard-to-torpedo attitude, and your leaky faucet becomes a thing of the past.

End To That Niggling Problem

Here’s a tenuous contention that displays the traditional proclivity to raise the hackles. But before your temper assumes rampaging dimensions, take a look at how you can put an end to your consternation:

• Cut off the water supply to the shower faucet, either in the bathroom or in the main cut off valve in the basement.
• Open the faucet to drain the water in it completely.
• Get to the root of the problem by removing the faucet handle screw, located underneath the snap on cover, with the help of a knife or screwdriver. This is achieved by turning the screw clockwise.
• It’s now time for the faucet handle to come off. At times, a slightly recalcitrant handle may be stuck to the stem, and comes out only after a few knocks with a hammer handle.
• Look for the rubber gasket inside, and inspect its condition. In case it coats your hand with a black deposit, it’s time to abandon it for a brand new one.
• Place the new ring flat inside the shower head assembly. It’s important to make sure that it fits perfectly.
• Retighten the handle, without the use of too much force. Similarly, thread the shower head into its designated place.

The Moment You’ve Waited For

It’s now time to turn on the water and see if you deserve a pat on the back. But what if things don’t pan out the way you planned? Relax; just unscrew the shower head, re screw it, and tighten the handle a little more. If it’s still as intractable as before, call a professional to bail you out.

Did you know that stopping a leaky shower faucet can be easy ? See http://www.SpicyKitchens.com

Article Source: http://EzineArticles.com/?expert=Yoga_Priyakara
http://EzineArticles.com/?Fix-Leaky-Shower-Faucet—Easy-and-Fast&id=1296625